Arrancando OpenWrt en ADB D.BG A4001N

Por fin arranca pero por ahora no fucionan el WIFI ni el puerto USB...


[    0.000000] Linux version 3.3.7 (chisco@chisco-aluminio) (gcc version 4.6.3 20120201 (prerelease) (Li2
[    0.000000] Detected Broadcom 0x6328 CPU revision 10b0
[    0.000000] CPU frequency is 320 MHz
[    0.000000] 32MB of RAM installed
[    0.000000] registering 32 GPIOs
[    0.000000] gpiochip_add: registered GPIOs 0 to 31 on device: bcm63xx-gpio
[    0.000000] board_bcm963xx: Boot address 0xb8000000
[    0.000000] board_bcm963xx: CFE version: unknown
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350)
[    0.000000] board_bcm963xx: board name: 963281T_TEF
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00002000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00002000
[    0.000000] On node 0 totalpages: 8192
[    0.000000] free_area_init_node: node 0, pgdat 8029d730, node_mem_map 81000000
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8128 pages, LIFO batch:0
[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Memory: 29416k/32768k available (2219k kernel code, 3352k reserved, 396k data, 196k init,)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 512
[    0.048000] NET: Registered protocol family 16
[    0.276000] registering PCI controller with io_map_base unset
[    0.284000] bio: create slab <bio-0> at 0
[    0.292000] PCI host bridge to bus 0000:00
[    0.296000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x11efffff]
[    0.300000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.304000] pci 0000:00:00.0: [14e4:6328] type 1 class 0x000604
[    0.304000] pci 0000:00:00.0: PME# supported from D0 D3hot
[    0.304000] pci 0000:01:00.0: [14e4:a8d8] type 0 class 0x000280
[    0.304000] pci 0000:01:00.0: reg 10: [mem 0x00000000-0x00003fff 64bit]
[    0.304000] pci 0000:01:00.0: supports D1 D2
[    0.304000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff]
[    0.308000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit]
[    0.312000] pci 0000:00:00.0: PCI bridge to [bus 01-01]
[    0.316000] pci 0000:00:00.0:   bridge window [mem 0x10f00000-0x10ffffff]
[    0.320000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[    0.324000] Switching to clocksource MIPS
[    0.332000] NET: Registered protocol family 2
[    0.336000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.344000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.352000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.360000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.364000] TCP reno registered
[    0.368000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.376000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.384000] NET: Registered protocol family 1
[    0.388000] PCI: CLS 0 bytes, default 16
[    0.388000] audit: initializing netlink socket (disabled)
[    0.396000] type=2000 audit(0.396:1): initialized
[    0.400000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.408000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat,.
[    0.420000] msgmni has been set to 57
[    0.420000] io scheduler noop registered
[    0.424000] io scheduler deadline registered (default)
[    0.432000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm63xx_uart
[    0.440000] console [ttyS0] enabled, bootconsole disabled
[    0.460000] bcm63xx-hsspi bcm63xx-hsspi.0: registered master spi0
[    0.460000] spi spi0.0: setup mode 0, 8 bits/w, 40000000 Hz max --> 0
[    0.460000] m25p80 spi0.0: found mx25l12805d, expected m25p80
[    0.468000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[    0.472000] bcm63xxpart: CFE boot tag found with version 6 and board type 963281T_TEF
[    0.480000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
[    0.488000] bcm63xxpart: Partition 1 is kernel offset 10100 and length eff00
[    0.492000] bcm63xxpart: Partition 2 is rootfs offset 100000 and length ef0000
[    0.500000] bcm63xxpart: Partition 3 is nvram offset ff0000 and length 10000
[    0.508000] bcm63xxpart: Partition 4 is linux offset 10000 and length fe0000
[    0.516000] bcm63xxpart: Spare partition is offset 2c0004 and length d2fffc
[    0.524000] 5 bcm63xxpart partitions found on MTD device spi0.0
[    0.528000] Creating 5 MTD partitions on "spi0.0":
[    0.532000] 0x000000000000-0x000000010000 : "CFE"
[    0.540000] 0x000000010100-0x000000100000 : "kernel"
[    0.548000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller thy
[    0.564000] 0x000000100000-0x000000ff0000 : "rootfs"
[    0.572000] mtd: partition "rootfs" set to be root filesystem
[    0.576000] mtd: partition "rootfs_data" created automatically, ofs=2C0000, len=D30000
[    0.584000] 0x0000002c0000-0x000000ff0000 : "rootfs_data"
[    0.592000] 0x000000ff0000-0x000001000000 : "nvram"
[    0.600000] 0x000000010000-0x000000ff0000 : "linux"
[    0.608000] bcm63xx-hsspi bcm63xx-hsspi.0: registered child spi0.0
[    0.644000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.652000] Registered led device: 963281T_TEF::internet
[    0.652000] Registered led device: 963281T_TEF::power
[    0.652000] Registered led device: 963281T_TEF::internet-fail
[    0.656000] Registered led device: 963281T_TEF::power-fail
[    0.656000] Registered led device: 963281T_TEF::wps
[    0.656000] Registered led device: 963281T_TEF::dsl
[    0.656000] TCP westwood registered
[    0.660000] NET: Registered protocol family 17
[    0.664000] 8021q: 802.1Q VLAN Support v1.8
[    0.680000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.688000] Freeing unused kernel memory: 196k freed
[    3.252000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 4, 100Mbps, full-duplex
[    3.412000] roboswitch: Probing device eth0:
[    3.416000] bcm63xx_enet: could not find a used port with phy_id 0, assuming phy is external
[    3.424000] No Robo switch in managed mode found, phy_id = 0xffffffff
[    3.432000] roboswitch: Probing device eth1: No such device
[    3.440000] roboswitch: Probing device eth2: No such device
[    3.444000] roboswitch: Probing device eth3: No such device
[   10.880000] Compat-wireless backport release: compat-wireless-2012-05-16-3-gde86a47
[   10.888000] Backport based on wireless-testing.git master-2012-05-29
[   10.896000] compat.git: wireless-testing.git
[   10.952000] cfg80211: Calling CRDA to update world regulatory domain
[   10.956000] cfg80211: World regulatory domain updated:
[   10.964000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   10.972000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.980000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   10.988000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   10.996000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   11.004000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   11.468000] SCSI subsystem initialized
[   11.512000] There is already a switch registered on the device 'eth0'
[   11.520000] roboswitch: Probing device eth1: No such device
[   11.524000] roboswitch: Probing device eth2: No such device
[   11.532000] roboswitch: Probing device eth3: No such device
[   11.836000] usbcore: registered new interface driver usbfs
[   11.840000] usbcore: registered new interface driver hub
[   11.852000] usbcore: registered new device driver usb
[   12.544000] Broadcom 43xx driver loaded [ Features: PNL ]
[   12.572000] Button Hotplug driver version 0.4.1
[   13.376000] PPP generic driver version 2.4.2
[   14.392000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.676000] NET: Registered protocol family 24
[   14.896000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   14.940000] nf_conntrack version 0.5.0 (462 buckets, 1848 max)
[   15.636000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   15.848000] usbcore: registered new interface driver snd-usb-audio
[   15.972000] Initializing USB Mass Storage driver...
[   15.976000] usbcore: registered new interface driver usb-storage
[   15.984000] USB Mass Storage support registered.
[   21.064000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 4, 100Mbps, full-duplex
[   21.076000] device eth0 entered promiscuous mode
[   21.080000] br-lan: port 1(eth0) entered forwarding state
[   21.088000] br-lan: port 1(eth0) entered forwarding state
[   23.092000] br-lan: port 1(eth0) entered forwarding state
[   34.676000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   34.692000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   34.700000] jffs2_build_filesystem(): erasing all blocks after the end marker...